patman

Was anything part of the exhaust system wrapped at all

Does make me wonder how your popping flames on a ct9 at 0.8bar what's the secret rob haha only having a few aftermarket parts aswell

You could always do it by getting little sticky paper and writing on them and sticking them to each sensor as you take them off, might be a good start and a little easier when putting it back together

I'm in sussex alittle far mate

Will have 2 GT seats by the weekend mate as got other ones to put in but depends where your located

I don't think it's petty at all mate they would soon be pissed if it was someone else doing it, or they have done what I see loads at night with other drivers, day time lights on so there dash is lit up but they haven't actually turned there lights on these modern cars have them these days don't they

Thankyou Colin mate sorry didn't mean the nipple side silly me meant the other hole which fits onto silicone hose which then goes on the intercooler pipe, my one is 25mm pm me please mate when you read this we talk there 👍🏻

Hello Colin what you think of it mate? If your happy with it you know I would be,ps do you know the hole diameter size? Cheers mate pat

Thanks for the message Neil Baileys are worse then forge so a lot have said a lot of negitive feedback about Baileys but thankyou anyway mate

Thanks for the tips lads, i will just leave it as it is then, I was gonna put it on, just because I had it for ages but will just leave it off now Thankyou

Brought a turbosmart of jdm-ep ages ago and was gonna fit it and see what the crack is, after doing lots of research I can not find what to set the actuator to? At the moment I am on 0.8bar, so I presuming the more I close the MBC it will then go to 0.7, 0.6 and so on so when it's fully shut there's no boost, and if I open the MBC fully it will be back to 0.8bar? Anyone shred some light on this please or am I wrong with all the above. Thanks Pat

Hello Gang Looking for a cheap Dumpvalve if anyone has any about, in good working order, can't afford to much, have gone through 2 second hand forge ones already maybe looking for something with a better sound too Cheers Pat

http://www.toyotagtturbo.com/wiki/EP82wiring/EP82%20Starlet%20Wiring%20and%20Connectors.pdf Page 10, horn is green and red, that's on an ep82

Are they the cheap kits from China mate?

Whatever's good for you mate 👍🏻👍🏻

That's good to hear, and yes mate but will do it eastbourne area next time 👍🏻

👍🏻👍🏻👍🏻

I'm pretty sure (let others comment too) is 28mm that's I.D

Good to see your still about mate, been awhile 👍🏻

http://japserviceparts.co.uk/toyota-starlet-turbo-glanza-v-ct9-turbo-to-downpipe-gasket-ep82-ep91-4efte-oe-japan.html?___SID=U, That's the cheapest I reckon your find mate unless someone on here has one laying around Also I'm pretty sure the bottom downpipe one most just use that gasket sealant stuff, as I have never seen a half decent gasket for the bottom part

Have you checked everything mate with the engine running? Even at the back where water pipes are, could be water pump seal, even heater matrix

I haven't no sorry Lawrence mate, now I can see why you need local to yourself after saying you had 2 delivered I will take back what I said, a few do come up from time to time mate so keep an eye out

So the other night in the early hours I was watching probably the most weirdest, (what the bloody hell is this) film, on film 4, it was called (under the skin) and it was made in Scotland, anyway sod all that a minute, there was a scene where she's at the traffic lights, and a car pulls up, where the bloke is out the window shouting at her, only to realise the car is a white ep82 GT turbo, think it had red mud flaps aswell, was just wondering was it anyone's on here or who owned it when it was in the film?

Please does anyone know the size of the clips what hold the outer plastic door trim on which has the GT turbo writing on it (pic below) eBay have loads but not sure what exact size I need. Thanks guys Pat

There's always post mate if your that desperate