Jump to content

JayJ

Member
 View Profile  See their activity

  • Content Count

    1012

  • Joined

  • Last visited

 Content Type 

Everything posted by JayJ

  1. JayJ
    Do you know water temps? If the temp sensor is not working, ecu will be in "warm up enrichment" state until water reaches 65c degrees.
  2. JayJ
    Just boosting around now. To do list is too long.. ..need to install cooling panel, tidy up Mitsuba's mounting brackets and buy new friction tyres for winter. Then maybe new wheels for next summer, injectors to get moar boooost or ebc to control bigger boost on mid range, better filter relocation, smaller ac condenser, projector headlights, panhard rod, front bumper and full repaint. Timescale is infinite! Also, if you are reading this and know everything about EMU, please PM ;-]
  3. JayJ
    14mm oil drain bolt is located bottom of the sump, facing a bit backward. If you are going to change the filter too, you will need approx 2.8litres of oil. 5w-30 or 10w-40 fully synthetic engine oil is recommended.
  4. JayJ
    You just can't beat this guy! https://www.facebook.com/photo.php?v=10203158026570392&set=vb.1199260427&type=2&theater
  5. JayJ
    Those are all made by Yoko, no personal experience, but people seem to use those on trackdays. Lot of reviews available too :-]
  6. JayJ
    How about Yokohama A539, S drive or A048 185/55/14 or 195/45/14
  7. JayJ
    Almost the same here, sensor sits just below the firewall and the wires go in through the big wiring grommet
  8. JayJ
    The car has been mapped now on Rototest VPA R5 chassis dyno with sweep mode. Sweep mode means accelerating constant predefined rate between 1000 - 8000rpm. Pulls were done in 5th gear and one pull lasted 30secs making it very accurate. The car was mapped with 1bar, as stock injectors are so close to maxing out, duty cycle 86%. The result is 107kw(145whp)@5960, torque 198nm@4510.
  9. JayJ

    Today is the day! ;-]

    1. Gainzy

      Gainzy

      Yes yes yes

  10. JayJ

    blitz ecu

    JayJ replied to HOK's topic in Electronics

    any chance to get a picture of the board?
  11. JayJ
    My car had exedy 3 paddle clutch when I bought the car and it broke in 2 years(jam ecu, blitz k1 1.2bar) with daily use. Currently running Helix organic fastroad, much easier and nice to drive around town. Only time will tell how much it can take, as I'm now running low 0.6 boost, soon to be mapped thou :-)
  12. JayJ
    Whitestar has 195/40 setup with ET35
  13. JayJ

    missing fuses

    JayJ replied to spoon's topic in Electronics

    Missing from my Glanza too, so let's say they are not needed
  14. JayJ
    He's sayin "allahu akbar" meaning god is greater or god is the greatest. I just can't understand what religion can do to a human mind.
  15. JayJ

    NGK ht leads

    JayJ replied to Gainzy's topic in Wanted

    Ultra's from Japland
  16. JayJ
    Was your car at level? I did oil and filter change today and used 3 bottles of Redline oil. One bottle is 1 quart = 946ml, making it total of 2.8l and oil level is just below top mark.
  17. JayJ
    2.8litres is the right amount with a filter change for 4e-fte.
  18. JayJ
    Can't stop buying things from Jpan
  19. JayJ
    Right one is trd and left one is C's, maybe for comparison edit: I was wrong first
  20. JayJ
    NO easy way, but some L-brackets and DIY
  21. JayJ
    Is compressor wheel tightened up as it should? If you spin it with your hand does it make any sound/hit compressor housing? Is the compressor housing tightened up as it should?
  22. JayJ
    Sounds like something went wrong with rotating it..
  23. JayJ
    Here's fast cut'n'paste. The wheels have been shot in a studio and the car in real life, so reflections make it look a bit weird And I'm not a pro photoshopper ;))
  24. JayJ
    Did you drive the car after installing the turbo and if yes, is it still smoking? Did you prime the turbo before the first start? Looks like the seal has gone, if it weeps oil out.
  25. JayJ
    Go to Google Play store, install TOYOBD1 app, open the app and you'll find an email address. I will get it MOT'd first this or next week and my hot pipe should arrive in a couple of days, so should be mapped in two weeks, if everything goes as planned. Removed the glanza decal today and didn't go well as paint chipped off with it! Boot's paintwork is poor as f*uck, so didn't come as though surprise.
×
×
  • Create New...