RoyalDutchie Posted August 21, 2020 Share Posted August 21, 2020 May be picking up some identical ones soon, in the Netherlands they are actually pretty common. Lots of people still drive starlets here and once they became to expensive they get broken for parts. Quote Link to post Share on other sites
burty Posted August 21, 2020 Author Share Posted August 21, 2020 15 minutes ago, RoyalDutchie said: May be picking up some identical ones soon, in the Netherlands they are actually pretty common. Lots of people still drive starlets here and once they became to expensive they get broken for parts. Honestly can say I can't remember last time I saw a glanza or SR on the road where I live in the UK must be 5 years ago, I do see a lot of 5 door ep91s though I think within the next few years parts will become expensive as seem to be getting discontinued, really want to make a proper job of this had it half my life now love the little thing Quote Link to post Share on other sites
Starletson Posted August 22, 2020 Share Posted August 22, 2020 My passenger door has rust on the bottom corner, kept getting scratched on the pavement. Seen an old boy in a faded red 3dr the other day and he gave me a wave, bless. Only see a few starlets floating about. Probably seen 5 ep91 near me over the last few years. Theres a 82gt for sale in bristol at the mo, not seen one of them in the flesh for 10 yrs i reckon Quote Link to post Share on other sites
burty Posted August 22, 2020 Author Share Posted August 22, 2020 My door was the whole bottom section very odd as everything else around it is fine must of had a seal fail? Replacement door has all seals attached so if that was case I'm sorted Quote Link to post Share on other sites
Starletson Posted August 22, 2020 Share Posted August 22, 2020 There must have been bare metal in there. Every time I open my driver door it drains all the rain water sat in it Quote Link to post Share on other sites
burty Posted August 22, 2020 Author Share Posted August 22, 2020 6 minutes ago, Starletson said: There must have been bare metal in there. Every time I open my driver door it drains all the rain water sat in it Il inspect it when I remove it see whats going on driver side is perfect Quote Link to post Share on other sites
burty Posted August 25, 2020 Author Share Posted August 25, 2020 Nothing major happened in last few days, I changed door handle as it was on borrowed time, changed gearbox oil as it was well overdue noticed the hose to the airbox is looking a little worse for wear so I'm gonna see if my new breaker mate has one, also may pick up a glanza strut brace are these worth while? Quote Link to post Share on other sites
Keviano27 Posted August 25, 2020 Share Posted August 25, 2020 The strut braces are abit of a pain to fit, you have to move the fuel filter but I've seen it been done. Think it's worth a go if it's cheap enough, might have to find this breakers myself! Sounds like a gold mine 😂 Quote Link to post Share on other sites
burty Posted August 26, 2020 Author Share Posted August 26, 2020 7 hours ago, Keviano27 said: The strut braces are abit of a pain to fit, you have to move the fuel filter but I've seen it been done. Think it's worth a go if it's cheap enough, might have to find this breakers myself! Sounds like a gold mine 😂 Nothings ever straight forward is it 😂 I did look at the fuel filter location but was hoping the brace would come forward and clear it.... Il see how much he wants before making any decisions Quote Link to post Share on other sites
Sam44 Posted August 26, 2020 Share Posted August 26, 2020 I feel your pain tried it myself. Lol. Modding time. Quote Link to post Share on other sites
burty Posted August 28, 2020 Author Share Posted August 28, 2020 On 8/26/2020 at 11:56 AM, Sam44 said: I feel your pain tried it myself. Lol. Modding time. looks that way lol Quote Link to post Share on other sites
stevie82 Posted August 31, 2020 Share Posted August 31, 2020 They do fit, it’s tight but I just pushed the fuel filter back Quote Link to post Share on other sites
Sam44 Posted August 31, 2020 Share Posted August 31, 2020 The issue I had was the inline diode pack on the wiper motor loom/plug. I'm not to sure what or why it's there, but the bar fouled it to the point it would not fit. Nice engine bay by the way. Quote Link to post Share on other sites
burty Posted August 31, 2020 Author Share Posted August 31, 2020 im gonna give it a go for what it costs thinking of spraying silver Quote Link to post Share on other sites
burty Posted September 1, 2020 Author Share Posted September 1, 2020 (edited) Right finally did a job I've been putting off because of the rust on the inner arch I've been meaning to remove the rear bumper to check the panels behind it as they are attached to where the bad inner arches are well I'm chuffed to bits they are in decent condition nothing a rub down won't sort got out the dreaded flat screwdriver and gave it a good poke it's solid most panels are discontinued so see this as a result the underside is getting the same treatment as the bodywork you see Edited September 1, 2020 by burty Quote Link to post Share on other sites
burty Posted September 1, 2020 Author Share Posted September 1, 2020 Also got thumbs off a lovely GT turbo near dinnington if was anyone one here Quote Link to post Share on other sites
Kieran Barber Posted September 1, 2020 Share Posted September 1, 2020 Yeah mate that was me, definitely made my day seeing it Quote Link to post Share on other sites
burty Posted September 1, 2020 Author Share Posted September 1, 2020 And me how bad is that round about must of spent 5 years of my sat in traffic there 😂 Quote Link to post Share on other sites
Kieran Barber Posted September 1, 2020 Share Posted September 1, 2020 It’s been terrible for years now mate, awful stuff lol Quote Link to post Share on other sites
Trevstar Posted September 2, 2020 Share Posted September 2, 2020 (edited) On 7/27/2020 at 4:50 PM, Pikey009 said: I'll take the genuine one off of the Black SR for you 😅 Never see them come up for sale anymore, i wonder how many cars with them fitted have been scrapped If ID-WORKZ have stopped making the replica TTE splitter, at some point I could possibly make a mold and make some up to sell 🤔 The replicas were only made from fiber glass and gel coated right? Decent work keeping the SR fit and healthy, hopefully for another twenty years! 👍🏻 Edited September 2, 2020 by Trevstar Quote Link to post Share on other sites
Pikey009 Posted September 2, 2020 Share Posted September 2, 2020 If you’re thinking of removing the one from your car to make a 3 hours ago, Trevstar said: If ID-WORKZ have stopped making the replica TTE splitter, at some point I could possibly make a mold and make some up to sell 🤔 The replicas were only made from fiber glass and gel coated right? Decent work keeping the SR fit and healthy, hopefully for another twenty years! 👍🏻 If you’re thinking about removing yours to make a mold then it may be tricky as I’m sure the body shop bonded it on As well as bolting it in place Quote Link to post Share on other sites
Trevstar Posted September 2, 2020 Share Posted September 2, 2020 (edited) 3 hours ago, Pikey009 said: If you’re thinking about removing yours to make a mold then it may be tricky as I’m sure the body shop bonded it on As well as bolting it in place Well I also have a replica one here somewhere, could make a mold of that? If I did make a mold, could you imagine a carbon fiber one? 😯 Edited September 2, 2020 by Trevstar Quote Link to post Share on other sites
burty Posted September 2, 2020 Author Share Posted September 2, 2020 11 hours ago, Trevstar said: If ID-WORKZ have stopped making the replica TTE splitter, at some point I could possibly make a mold and make some up to sell 🤔 The replicas were only made from fiber glass and gel coated right? Decent work keeping the SR fit and healthy, hopefully for another twenty years! 👍🏻 Thanks mate so much love for this car admitedly sometimes it's gone on back burner with other projects etc promised myself I'd get it back to its former glory and its finally happening now Quote Link to post Share on other sites
burty Posted September 2, 2020 Author Share Posted September 2, 2020 8 hours ago, Pikey009 said: If you’re thinking of removing the one from your car to make a If you’re thinking about removing yours to make a mold then it may be tricky as I’m sure the body shop bonded it on As well as bolting it in place I wouldn't expect anyone to remove a genuine one if it was bonded imagine if it was to break how gutting would that be I only know of 2 in existence, how's the GT coming along? Quote Link to post Share on other sites
burty Posted September 2, 2020 Author Share Posted September 2, 2020 5 hours ago, Trevstar said: Well I also have a replica one here somewhere, could make a mold of that? If I did make a mold, could you imagine a carbon fiber one? 😯 Carbon fibre would be lovely, I've been looking for copy's for months and there simply aren't any the NA needs some sort of lip imo Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.