Jump to content

Johnboy GT

Member
 View Profile  See their activity

  • Posts

    1346

  • Joined

  • Last visited

 Content Type 

Everything posted by Johnboy GT

  1. Johnboy GT
    What about sat at traffic etc? Correct there would be minimal I suppose when driving. John
  2. Johnboy GT
    Lovely example. Same gauges as mine, did you have any difficulty wiring your's in? John
  3. Johnboy GT
    You can do it but you have moved your intercooler from there so there is no chance of heat soak so to me it seems pointless putting your oil cooler there? John
  4. Johnboy GT
    That's what I was after! Cheers boss John
  5. Johnboy GT
    Morning Looking for someone to tell me the easiest way to change my CV boots. Where is best to split the drive shaft and any problems I am likely to incur. Any help would be greatly appreciated as this is one of the last few jobs on a dwindling mot list. Cheers John
  6. Johnboy GT
    That is a Laguna Splitter. Or you can get an Espace splitter dude John
  7. Johnboy GT
    Looks lovely bud. What did you paint the rear floor with? John
  8. Johnboy GT
    Seats look lovely mate. Very similar to what I had in mind for mine. Going to ask a question so apologies if it's daft but why have you crossed over your harness at the back? John
  9. Johnboy GT
    Lovely car, what coilovers are they as it looks alot lower at the rear than mine? John
  10. Johnboy GT
    This has happened to me also. Checked the clearances, swapped with a known good head and cams and it's still there. Is it possible the tension of the cam can cause it? John
  11. Johnboy GT
    The cone on the fitting is where it seals. Check that there isn't a flat spot on the cone mate. John
  12. Johnboy GT
    Hoses on the back of the inlet manifold on the correct way round? John
  13. Johnboy GT
    Glad you got it sold bud. Hope to see you in another shortly John
  14. Johnboy GT
    Found your add on Gumtree bud. I wouldn't have said it was badly priced really, bit of a downer having no MOT but if you know what it needs and it isn't much then I'd stick to your guns John
  15. Johnboy GT
    My dad had one of these in black which I can vaguely remember. He's says it's the best car he's ever had! Loving it! John
  16. Johnboy GT
    Out of curiosity would a lightweight pulley without the dampener cause a ticking noise? John
  17. Johnboy GT
    Genuine toyota head to manifold gasket. What turbo kit are you using? You won't need any paste for these gaskets anyway. John
  18. Johnboy GT
    Buy the weld in fittings and take it to any welder and they would manage. Or Dean at RW Developments or check the Facebook page Guess Worx I think it is. John
  19. Johnboy GT
    Perseverance. I took the arm off the car, cut as close to the base of the metal back plate on the bush, hammer and chisel. Came off eventually. John
  20. Johnboy GT
    I'll get a photo and see what you think. Unless I'm being dim but I'm pretty sure I've lost a part from somewhere. John
  21. Johnboy GT
    Is that Del boys van there!? Looks alot better mate! John
  22. Johnboy GT
    Ahh you are a gentleman. I'll get a photo tonight and post it. I'm assuming I've lost a bit for the top as it worked before I took the engine out the car. John
  23. Johnboy GT
    Can always plumb it back to standard and have it sit in the engine or on the rocker....
  24. Johnboy GT
    Spot on bud. Going t persevere with wd40 but I'll order a rebuild kit just incase. May buy those calipers off you incase as well. John
  25. Johnboy GT
    I've rebuilt a few calipers so I shouldn't stumble too much 😂 John
×
×
  • Create New...