Jump to content

daniel_g

Member
 View Profile  See their activity

  • Content Count

    10875

  • Joined

  • Last visited

 Content Type 

Everything posted by daniel_g

  1. daniel_g
    That had been on tradecarview for ages, wasnt anywhere near 7k either haha chancing bastards. Do like the Livesports front bumper, but it needs the rest of the kit to pull it off.
  2. daniel_g
    Is there an option for garden ornament? When its on the road its a daily
  3. daniel_g
    Always liked these, needs a 1J though
  4. daniel_g
    Think its a ZEP Type 2, never seen anyone on here with one.
  5. daniel_g
    A polish dude with a pikey trailer in your contacts list is al ya need haha
  6. daniel_g
    Or just an actual car that you can drive is pretty fun too..
  7. daniel_g
    Mind seeing that from a while ago i think it looks alright
  8. daniel_g
    Is it already mapped?
  9. daniel_g
    People might tell ya different but id run it standard fuelling till its run in, then set it up after that.
  10. daniel_g
    If youre engine hasnt been run in yet id put a standard fpr on. You dont want excessive fuel / bore wash on your new motor. Ideally you want it set up on a dyno with a wideband.
  11. daniel_g
    Do like
  12. daniel_g
    It would prob cost well over a grand at a guess dude, welders labour aint cheap. Still seems a bit shady to me, when Mikey done his it looked bent as fuck, never seen an alignment printout for it. Dont think so dude, i might get something similar done when i inevitably blow the rear axle yo fuck on the 4paw.
  13. daniel_g
    Cutting the axle and adding shims seems a bit pikey to me.. Swap the axle out for a proper IRS setup. This ones a pic of a mx5 subframe, do away with the rwd stuff, plenty of aftermarket arms etc available, the wheelbase cant be far off, better brake setup, 4x100 stud pattern.
  14. daniel_g
    That scoop!
  15. daniel_g
    You can still get rolling shells cheap, normally with a fair bit of stuff on them, a lot of parts are still cheap too. Although that means time and effort lol.
  16. daniel_g
    Know Browners V sold for about 10k. Starlets are going up in price, have been for the past while. Breaking is for sure the best way of getting your cash back.
  17. daniel_g
    5e blocks and cranks dont come up for sale as often as they used to. Hope the wisecos fit! Couldnt turn em down at under 400 posted from the states. The rods are about 200 new.
  18. daniel_g
    Its the maxsppeding rods im using, the dude thats gonna build my engine swears by them. He did say to buy JE pistons but i got a set of brand new in the box Wisecos for a good deal. If they dont fit i'll sell them and get JE ones... or sell the rods and go down the 5E route
  19. daniel_g
    I think JE do. I bought Wiseco for mine but the engines not built yet.
  20. daniel_g
    Try it on a 4paw on the deck lol
  21. daniel_g
    This is now coke cans. Lock and delete!
  22. daniel_g
    Adamans white V had one, thats the only one ave seen in the UK. And thats going back years.
  23. daniel_g
    How the hell is it STILL at TD!!? Glad it'll be back soon, need to see this in the summer!
  24. daniel_g
    See youve swapped back to a standard inlet, was the aftermarket inlet having an effect on the spool time?
  25. daniel_g
    Should be carry out a BET test, it wont meet the min limits. Then its goes down to if its between 92 - 95, they wont be able to find an exact match. So it gets a non CAT test which is has very lenient min values of CO = 3.5% and HC 1200ppm. I've been getting pestered to sit my MOT test for a few years now but i refuse because its far too much hassle haha.
×
×
  • Create New...