Jump to content

5e colin

Club Member
 View Profile  See their activity

  • Posts

    6604

  • Joined

  • Last visited

 Content Type 

Everything posted by 5e colin

  1. 5e colin
    rad cap fucked and spitting coolant if the theremostat is stuck open she would take aaaaages to over heat maybie gasket failure
  2. 5e colin
    you wlill have to fit a rising rate fuel pressure regulator and a 255l pump are you na or turbo whats your plan/spec
  3. 5e colin
    probly input shaft bearing or clutch release bearing
  4. 5e colin
    no man no bolt on /of part needs pulling out its also mot fail if they spot it because there is a wrinkle zone 2 inch back of there !!!!! its not the end of the world that it looks minor my glower was crushed much harder and that pulled out fine ( ish )
  5. 5e colin
    bend the bracket to the rear of the car its that that tensions it to spring open 1s the lever is pulled you just havent bent it far enough keep your lever up bend it till you feel it starts touching and pushing back out it works the same way on my gtt i checked
  6. 5e colin
    if the ct9 is fucked you can take the core out and weld up the main shaft hole so no burning oil can get in it just take compressor and the shite of block oil feed and return you will have mint emissions
  7. 5e colin
    the 2nd spring is usually for higher boost level in those kits like 10psi spring and 4psi spring together they make a bar etc etc
  8. 5e colin
    or trow rocks at it only have to hit it 1s wont come back / stinking rodents
  9. 5e colin
    yup to much boost and ecu conked her out kid ut to high on the boost on stock ecu and injectors ( 0.5max !!! ) ecu will have seen lean condition on the sensor and an cut i bet if you do a diagnostic test you will get code 25 contineus ( lean ) condition turn her back down before u blow your 4efte kid
  10. 5e colin
    hey lads anyone have a cheap toyosports decat lying around
  11. 5e colin
    i sugest to use same size tb as your piping intercooler piping is you could use the stock 4efte 1 at 50mm i would keep pipes as small as possible without restricting
  12. 5e colin
    you could ( BUT ) it might not work and now u fucked your loom up for nothing try to de pin the connector so you can go strait from ecu to knock to figure out whats what there
  13. 5e colin
    from ecu plug mate depin the pin on the plug and run the whole wire to the knock sensor if it works then run it tru the firewall and tape it up on the loom dont be butchering your current loom till your certain of it
  14. 5e colin
    yes big difference in weight 3 kilo 4efe and 4efte flywheels are the same size its only the clutch mounting dowels are in a diferent spot for larger pressure plate
  15. 5e colin
    guys this thread is 1 year old !!!!
  16. 5e colin
    some cat diner with rat poison in it
  17. 5e colin
    its not the car its always the peeps standing in front of them that make the issues we just cant leave them alone ha ha
  18. 5e colin
    great seller well packaged to, buy with confidence will buy again of him
  19. 5e colin
    ar you pluged in on top of the waste gate or bottom ? try the other port ?
  20. 5e colin
    mine oem on the gtt is bolted so must be on the glanza v to
  21. 5e colin
    if it was mine i would say strip to bits every nut and bolt start cleaning clean the oil gallerys oil relieve everything pick up etc etc etc inspect bearings the lot very big chance you fit new pump without cleaning it that it will fail again
  22. 5e colin
    hey thanks for the link mark :) are you using 304 or 316 and short radius or long radius , and where did the ss flanges come from ? sorry about the questions
  23. 5e colin
    o would measure and drill the holes so it bolts on then put a bonding agent on it to gets rid of the spoiler rattle
  24. 5e colin
    sounds like you didnt clean the whole internal block there where probably metal debri i the oil channels or you really over tightened the belt ??? ( don't think so ) other possibility is you starved the pump from oil on first start up and where running a tat without oil circulation until it pressurised ( blocked pick up ) ?
  25. 5e colin
    thats freaking nice the mani mark where did you buy the ss bends and pipes ???
×
×
  • Create New...